Do you love fishing? Are you having a hard time finding fishes? Then you have absolutely nothing to worry about. I have just the right solution for you. All you need is a fishfinder.
Kayak Fish Finder Install: Fishfinder is a tool that is used by fishermen to locate fishes in the water. It is a very simple tool that helps locate the presence of fish in the water.
It is very useful for you if you run a business involving fishing. You can also use it if you often go on fishing trips as a hobby.
Although using a fish finder is a piece of cake, there a few things you need to know before using it. I will help you understand how exactly it works and how can you install it. Also, many other things might pique your interest.
Note: There are many sonars in the market, but finding the best sonar fish finder for a kayak is challenging due to many varities and offers.
- 1 Working Principle Of Kayak Fish Finder Installation
- 2 Tools You Need for Installing the Fish Finder
- 3 Best Kayak Fish Finder Installation Kit
- 4 1. Hobie Kayak Fish Finder Install Kit
- 5 2. Hobie Kayak Fish Finder Installation lithium in a Kit for I Series:
- 6 3. Humminbird 7400931 MHX XNT Transome Mounting Hardware kit
- 7 4. Hobie Lowrance Fish Finder Lithium-ion Installation Kit:
- 8 5. Raymarine Axiom R-V 100 real vision SD All-in-one Transom Mount Transducer
- 9 Step By Step Installation of Fish Finder On Kayak
- 10 Head Unit Placement: Locate the Unit Where You Can Mount Fish Finder
- 11 2. Transducer Placement: Locate Place in the Kayak to Set Transducer
- 12 3. Installing the Transducer on the Kayak
- 13 4. Wiring and Soldering of the Fish Finder
- 14 5. Battery Setup: Kayak Fish Finder Battery Install
- 15 Note: After Party Clean-up: How to Clean Kayak And Fish Finder After Fishing?
- 16 Kayak Fish Finder Installation Accessories
- 16.1 Lowrance 000-10261-001 DSI Transducer Trolling Motor Adaptor
- 16.2 ADVANCED ELEMENTS AE2042 Accessory Frame System, Gray, One Size
- 16.3 Expert Power EXP1290-2 Black lead-acid-battery, 2 Pack
- 16.4 Humminbird 710276-1 XP 9 HW T Helix Dual Spectrum Chirp with Temperature in-Hull Transducer
- 16.5 Humminbird 710270-1 XTM 9 MDI T Helix (MEGA DI) Trolling Motor Mounted Transducer
- 16.6 Humminbird 740173-1 IDMK S10R Reinforced In-Dash Mounting Kit, SOLIX 10 Fishfinders
- 16.7 Scotty Kayak/SUP Transducer Mounting Arm with Gear-Head
- 16.8 Yakattack Nocqua Pro Power Kit 10Ah
- 16.9 Mantis Dock Light Add-on Light full-colour RGBW Spectrum
- 16.10 Garmin 200-kHz and 50-kHz Transom Mount Transducer Kit-15-Degree Beamwidth
- 16.11 13150 Faria Dress White Deep Transom Transducer
- 16.12 Greenlee FF200 fishfinder Plus Vision System
- 16.13 Humminbird 780028-1 UC H5 Unit Cover for Helix Series
- 16.14 Deeper Flexible Arm Mount 1.0 – Easily mount Deeper PRO-series Fish Finder to Kayak / Boat in secs
- 16.15 Yakattack GTTL175 Geartrac Top Loading Aluminium Kayak Mount Track
- 17 Frequent Ask Question Of Kayak Fish Finder Installation
Working Principle Of Kayak Fish Finder Installation
Working with fishfinder appears as a high-tech process. But truth be told, it has quite an easy functioning. It is based on the principle of reflection of ultrasonic sound waves. It operates on the technology of the SONAR System.
The use of this technology dates back to the 19th century. Since then many advancements have taken place concerning its processing and features.
Fishfinder has a LED or CRT monitor. The location of the fishes is displayed on this monitor.
First, a transmitter is installed on the kayak. It continuously transmits signals which are converted in to sound waves before sending it into the water. The SONAR System exercises in the technique of the Echo to reflect signals to the transmitter.
When the sound wave hits anything in the water, it reflects. On reflecting, it displays the composition, size, and shape of the object it hit. The degree to which it can be interpreted is based on the frequency and power of the signal that is transmitted.
The distance of the object in water can be calculated by knowing the exact speed of the sound wave in water.
To avoid receiving false signals from other insignificant things, reflection due to fishes is illustrated differently. This avoids confusion from signals reflected from seaweeds or corals. The echo varies in magnitude and form in the presence of fishes.
On the fishfinder monitor, the presence of fish is marked using its symbol. This detection process can be repeated up to 40 times per second.
Tools You Need for Installing the Fish Finder
Before getting on with the installation you need to take a trip to the hardware store. There are certain tools you need while installation of the fishfinder.
- Power Drill
- Heat Gun
- Different size bits
- Wire caps
- Mount & Adapter
- Bits & Steel crews
- Depth finder
- Socket Wrench
Best Kayak Fish Finder Installation Kit
There are hundreds of fishfinders installation kits available for a kayak. It often leads to confusion and you end up taking the wrong decision. So I will help you find the ideal installation kit for your kayak.
Here are some of the best fish finder kits available for kayaks
1. Hobie Kayak Fish Finder Install Kit
This kit is manufactured by Hobie and can be used in any Hobie kayak with the Lowrance Ready feature. The kit includes a 12V 9AH waterproof gel cell battery along with a charger. It also has the wiring hardware needed for installation. The kit comes with 4 wire connectors, 1 through-hole wire plug, and 3 zip ties.
2. Hobie Kayak Fish Finder Installation lithium in a Kit for I Series:
This kit is manufactured by Hobie. It helps you install your fishfinder into your Hobie I series inflatable kayak. The kit consists of a 12 V, 10 AH Nocqua lithium-ion battery along with a 12V battery charge. You also get a fishfinder console mount and a radar mount. Wire connectors and 3 zip ties are also provided.
The best feature of this kit is that you can fit it on any Hobie Mirage kayak which has a Lowrance ready plate.
3. Humminbird 7400931 MHX XNT Transome Mounting Hardware kit
This kit is used for XNT Transom- mount transducer. It consists of kick-up brakes along with a transducer bracket plug. The kit has been designed in such a way that it can be particularly used in the marine environment. Several transducers are compatible with this kit.
The key feature includes that it integrates with XNT 920, XNT 920T, and many others of the same series.
It comes with a one year warranty and hardware required for mounting XNT transducer.
4. Hobie Lowrance Fish Finder Lithium-ion Installation Kit:
Manufactured by Hobie, this kit allows you to install fishfinder on a Hobie kayak. It should possess the Lowrance Ready feature. It is powered with an ultralightweight Nocqua lithium-ion battery.
The battery is 12V 10AH along with it you are also provided with a 12V battery charger and a 12V battery holders. The kit includes wire connectors and zip ties. It does not include a console mount.
5. Raymarine Axiom R-V 100 real vision SD All-in-one Transom Mount Transducer
This is SD all in one transom mount is featured with 4-channel wide spectrum CHIRP transducer along with Down vision and side vision. It has high-frequency CHIRP and Real Vision 3D sonar.
Along with a BUILT-in attitude, it has a heading reference system that helps stabilize sonar images, which in turn compensates for vessel motion. It is characterized by rugged marine-grade stainless steel mounting. It has integrated kick-up to avoid damage.
Step By Step Installation of Fish Finder On Kayak
Installation of fishfinder is quite easy if you know how to go about with the procedure. There are many techniques are using which you can install the device. I will show you some of the easiest ways to install your fishfinder.
Firstly you need to know that there are 4 main aspects of the installation of fishfinder transducers. They being:
- Head Unit placement
- Transducer placement
- Battery Setup
Head Unit Placement: Locate the Unit Where You Can Mount Fish Finder
Foremost you need to decide where exactly you want your fishfinder monitor to be. It depends on the type of kayak you use. I use a pedal kayak, so I can install the transducer on the sides of the kayak. Because of this, the monitor is close to the seat. You merely have to drill and fix RAM mount on the side of the kayak.
The main advantage of using a RAM mount is its adjustability and portability. You simply need to fix it on the kayak and tighter the ball mount. The ball mount allows us to rotate and have any position and head angle. Important features also include its compact size and less coverage of space.
If you have a paddle kayak then it is impractical for you to fix your head unit on the side. You will end up smacking your paddle on the unit. I recommend you to install the unit, forward into the dash. In this way, it will be in front and out of your way. If you want images like we used in our post you can check our other site for free indian stock photos
Installation of Transducers:
Of the whole installation process, this is the most complex part. Some manufacturers make it easy for us by providing scuppers. In some kayak, you will find a scupper located in front of the cockpit.
If you follow it down underneath the kayak, you will find a location for installation, pre-drilled, and ready for the mounting transducer. A similar scupper can be found at the rear end. There are some brands such as Hobie which provide skid plate for installation.
2. Transducer Placement: Locate Place in the Kayak to Set Transducer
It is also known as through-hole transducers mount. For this technique, you will need a high-density waterproof foam. I suggest you opt for a fairly thick foam. Place the transducer on the block. Mark the outline of the transducer.
Leave space on all sides to stick it on the boat. Now, cut through the block. Use a sharp knife to do so. Make sure you have a nice and clean cut. See if the transducer fits firmly. Decide where exactly you mount your transducer to be.
I prefer it to be right underneath me. clean the area using sandpaper. Now using silicone sealant like goop. .Stick the block on the designated location. While sticking make sure the transducer is pointed forward. Use enough amount of glue.
Make sure there are no air bubbles. Now place some weight on it and let it dry. It takes about 24 hours to dry off. Now that you are finally done, pour some water into the cut and see if it leaks. Now place the transducer on the water. See that it touches the water surface. And you are done!
Don’t fix the transducer right at the tip of the kayak as it will sailing and disturb continuity. One setback of this technique is that it does not give accurate temperature reading. Other than this, I find no difference in sonar reading and down imaging.
3. Installing the Transducer on the Kayak
If you want the easiest way out, you can go for the flexible RAM Mount Transducer available in the market. You simply need to attach it to the arm of the kayak.
The mount has a flexible arm. You just have to put the arm with transducer inside water while sailing. You can keep the arm off the water surface to avoid drag.
4. Wiring and Soldering of the Fish Finder
In case of wiring, you need to make sure you keep it off your way. You can stash it up underneath your seat or in the side pockets. Some manufacturers also provide a battery box or compartment to bundle the wiring. For wiring, you can use different wiring kits available.
It comes with different styles, plug adapters, etc. For example, if you are using both transducers and power cord, you will need a double hole system. You can lock a little rubber piece into the gap and create a watertight seal through the hole of your kayak.
5. Battery Setup: Kayak Fish Finder Battery Install
Kayak fishfinder Battery InstallYou always must take your battery power, an SLA (Sealed Lead Acid) battery life. Such a battery works with the protection of the acid being sealed within the plastic instance of the Battery. Since there isn’t any prospect of this acidity being spilt as the kayak floats to the 25, this is a perfect battery to get the kayak.
Check the Capacity and Sizes of the Battery for Proper Installation
Assess the Ability and Collars of this Battery for suitable Setup These batteries can be found in lots of diverse sizes, but probably the many available sizes are 7, 1-2, and 18Ah. Kayakers utilize battery packs for fishfinders.
Battery capacity is measured in Ampere Hours (Ah). An Ah is 1 amp for an hour. Thus a 12Ah battery is capable of supplying 1-2 amps for one hour amp for approximately 1-2 hours but more than that.
A Place for the Battery of the Fish Finder
As an instance, of a FishFinder that is 250mA needs one-quarter of the amp. If you’re planning on fishing for 6 hrs so afterwards you’re going to have to have atleast a 1.5liter battery. Remember, you should never take the Battery. Bearing this in your mind, you might desire to buy a more 3.0Ah or more rated battery.An area for your Battery of this fishfinder search for a location for your battery power within your kayak, keep it from saltwater. Salt-water can short the Battery out if the seawater can rust underwater, and also the battery terminals.
Protecting the Battery
Fixing the Battery, you’re able to protect the Battery using a battery or perhaps even a foam block. Decide on a foam block that is fresh and then indicates the middle of this foam. Slice the foam leaving the inch gap. Paste the foam onto your kayak to help keep it from the saltwater’s human body.
Additionally, remember to take your battery package’s charger. Don’t use a car battery charger or some ordinary since your SLA battery will be damaged.
Note: After Party Clean-up: How to Clean Kayak And Fish Finder After Fishing?
Once you are back from your fishing trip you must clean your kayak. The kayak is exposed to seawater and debris from the sea. If you do not clean your kayak every time you go fishing then it might cause damage to it. The same is the case with your fishfinder transducer.
Don’t Use Hot Water
To clean your kayak, wash it thoroughly with fresh water. Make sure you get rid of all the debris. You can use a soap or a mild detergent if you like. Make sure you clean it up properly. Stack up the kayak upside down to let all the water out properly.
Check if the Device is Waterproof for Water Cleaning
To clean your transducer you must use a soft cloth. Do not clean it harshly as it might damage the transducer. Make use of sharp objects to get rid of debris tangled in the transducer. Do this carefully. If you follow all the steps carefully you won’t have a hard time installing and using your fishfinder.
Note: (New Post Published) Best Fish Finder For Kayak Review & Guide (Update 2020)
Kayak Fish Finder Installation Accessories
Lowrance 000-10261-001 DSI Transducer Trolling Motor Adaptor
This product is designed in such a fashion that allows you to mount a DSI transducer to the bottom of a trolling motor. It is intended to work with a skimmer transducer for down scan imaging sonars. This product enables you to have a clean and professional installation look. It weighs about 3.2 ounces and works only with DSI units. The kit consists of a trolling motor snap-on mount along with stainless steel trolling motor clamp. You are also provided with 2 zip ties with it.
ADVANCED ELEMENTS AE2042 Accessory Frame System, Gray, One Size
It is an accessory frame system that you can fix on your kayak. You can easily customize it to any kayak you want. It can carry any aftermarket item which has a 1-inch rail mount. You will find mounting grommets and other accessories included in the kit. The least possible installation surface is about 23″ wide.
Expert Power EXP1290-2 Black lead-acid-battery, 2 Pack
It is a sealed Lead-acid battery manufactured by ExpertPower. It is a 12V 9A 20 hours battery with F2 style terminals. Easy installation. It has a robust construction and is highly resistant to shock and vibrations. It is also chemical and heat-resistant It has a spill-proof design. The product dimensions can be given as 5.94×2.5×3.71inches.
Humminbird 710276-1 XP 9 HW T Helix Dual Spectrum Chirp with Temperature in-Hull Transducer
As the name suggests, it is a dual spectrum CHIRP along with an in-hull temperature transducer. The CHIRP has a range of 150-220khz and its maximum depth is about 1200ft. Kindly note that this transducer does not support side imaging or down imaging. It has a dual spectrum sonar.
Humminbird 710270-1 XTM 9 MDI T Helix (MEGA DI) Trolling Motor Mounted Transducer
It is a trolling motor transducer with digital CHIRP dual spectrum 2D. It also has digital CHIRP Mega imaging. The coverage provided by the dual spectrum 2D CHIRP is about 25°& 42°@-10dB. It has a trolling motor mounted on it. It is not compatible with any model other than MEGA Helix models
Humminbird 740173-1 IDMK S10R Reinforced In-Dash Mounting Kit, SOLIX 10 Fishfinders
It is an in-dash mounting kit. It is about 22.86×32.39×19.69cms. It fits perfectly with SOLIX 10 models.
Warning: Kindly note that this product exposes you to some chemicals such as lead. They might be injurious to your health.
Scotty Kayak/SUP Transducer Mounting Arm with Gear-Head
It is a transducer arm mount manufactured by Scotty and has a Gear-head adapter. The mounting arm is very strong and corrosion-resistant. It also has a Slip Disc if you want micro-adjustments. The kit also consists of 438 Gear Head Track Adapter. It works along with Scotty Slide Track. It can quickly drop & lock fishfinder mount. The transducer arm has a wide spectrum ranging from 11.5 inches to 18 inches. It can be rotated up to 360°.
Yakattack Nocqua Pro Power Kit 10Ah
It is a 12 V lithium-ion battery. It is waterproof and rechargeable. It is very lightweight and small in size. It comes with a silicone sealed case. It has open end connectors.
Mantis Dock Light Add-on Light full-colour RGBW Spectrum
It is a complete ready-to-install kit. It is very easy to install. You have to power it using a standard 4GFCI outlet 110 V AC power source. Its unique features include 3 full-colored RGBW dock lights. You can integrate it using a 30′ heavy-duty cable. The dock lights are manufactured using marine grade bronze housing. You will find that it has a zip mount universal mounting system.
Garmin 200-kHz and 50-kHz Transom Mount Transducer Kit-15-Degree Beamwidth
It is a transom mount made up of plastic. It operates on 200kHz and 50 kHz operating frequency. The beamwidth at 200 kHz about 10 degrees and that at 50 kHz is about 40 degrees. The kit includes all the hardware required for mounting
13150 Faria Dress White Deep Transom Transducer
It is a depth finder manufactured by Faria. Its maximum capacity is 199 foot (61cm) deep. It has a big display with background light. This helps in clear reading during might time. It is water-resistant. It can be fitted into a 2-inch hole. It features audible and visual alarms.
Greenlee FF200 fishfinder Plus Vision System
It is designed is such a way that it can safely view and troubleshoot any errors in energized wires. The kit consists of a handheld display unit. You will also find 4-AA batteries and a USB cable along with other mirror tip accessories. It has in-built memory of capturing over 2000 photographs.
Humminbird 780028-1 UC H5 Unit Cover for Helix Series
It is a cover for the gimbal mounter Helix Series 5 fishfinder. The material used is neoprene. Take note that you are not supposed to use it during hauling of the Boston the trailer.
Deeper Flexible Arm Mount 1.0 – Easily mount Deeper PRO-series Fish Finder to Kayak / Boat in secs
It is a flexible arm mount with a 50 cm aluminum rod which can be easily bent. It can be integrated with RAM mounts you can easily install it. You can fix it on both metals as well as plastic material. The kit includes a security strap and a crab clamp.
Price: $ 49.50
Yakattack GTTL175 Geartrac Top Loading Aluminium Kayak Mount Track
It is a heavy-duty surface mount track. It provides amazing adjustability for mounting your accessory. It is highly compatible with 1/2″ wide track hardware. It allows you to install it from the top. You do not require access to the backside. The package also includes screws required for installation.
Check Our Other Blogs: Fish Finder Review
Frequent Ask Question Of Kayak Fish Finder Installation
ow Much Does It Cost For The Installation Of Fish Finder?
If you get a marine electronics installer to help you install your fishfinder transducer, they may charge you about $80-10 for an hour. Altogether it might cost you about $200-300 you follow the steps and install it yourself you will spend a lot less
How To Fix The Transducer At The Proper Level?
The easiest way to level your transducer is to use a protractor level. The level inside it can be adjusted. Get your kayak in the water. Place the protractor level on the arm of the kayak and adjust the bubble to the centre. Now get the kayak out of the water and place the protractor level back to the same position. Now jack your trailer accordingly until you get the same level. Once you do that, you simply need to adjust your transducer by placing something underneath it. Level the transducer by getting the bubble in the centre.
How To Install a Fish Finder Battery?
Installation of fishfinder battery includes proper wiring of the battery to the display unit and the transducer. Install it where it is easily reachable and out of your way while paddling. It is recommended that you use a battery box to hold your battery. It also avoids contact of battery with water.
How to Install a Fish Finder Display?
You can mount your display using a RAM mount. Install it in such a way that it does not obstruct your way. You can fix it by drilling holes and sealing it on the kayak.
Which Hat is the Best Place for Transducer Installation?
The best place to install a fishfinder transducer is right underneath where you are sitting. In this way are vertically above the transducer which makes it a lot easier to work with.